Skip to content

TV on plasterboard wall: which fixings hold, and when to find the studs

Alex6 min read

Quick answer

Yes, a TV can go on plasterboard if the bracket is fixed into the timber studs or with heavy-duty cavity fixings rated for the load. GripIt rates its 25 mm fixing at 113 kg safe load straight down, but only 20 kg pulled straight out, and the safe load falls as the TV sits further from the wall.

Key takeaways

  • GripIt's datasheet gives a safe shear load of 113 kg for its 25 mm blue fixing and 93 kg for the 20 mm brown, tested on 15 mm plasterboard.
  • The same datasheet gives only 20 kg safe tension per fixing, for every size.
  • At 150 mm from the wall, the blue fixing's safe cantilever load falls to 25 kg, GripIt says.
  • GripIt says safe loads reduce on thinner board, down to a 9.5 mm minimum.
  • Samsung lists 400 by 400 as the usual VESA pattern for 46 to 75 inch TVs.
  • Moving a socket for the TV onto a new circuit is Restricted Works for a Registered Electrical Contractor (HSA).

113 kg

safe shear load, one 25 mm GripIt fixing

GripIt datasheet

20 kg

safe tension load per GripIt fixing, any size

GripIt datasheet

25 kg

safe load, 25 mm fixing, 150 mm from the wall

GripIt datasheet

Plasterboard is everywhere in Irish homes. It lines timber stud partitions in newer houses and apartments, it is stuck to block walls with dabs of adhesive, and it covers metal frames in many apartment blocks. Each one takes a TV differently. The board itself is not strong, so the job is about what the fixing grips.

Will a plasterboard wall hold a TV?

Yes or no

Yes, in most cases. Fix the bracket into the timber studs behind the board where they line up, or use heavy-duty cavity fixings rated for the load. On dot-and-dab walls, fix through to the block behind. Ordinary masonry plugs in plasterboard are not suitable for a TV.

The Assembly Crew, a Waterford fitter, puts it simply. A plasterboard wall on timber studs or a metal frame needs the bracket fixed into the studs or with fixings made for hollow walls. Where a large screen on a swing arm is too much for the studs, it offers a fixed bracket or another position.

Our TV wall mounting service brings fixings for each wall type and starts from €110 per TV.

How do you tell what your wall is made of?

Short answer

Knock on it. The Assembly Crew’s test: a dull, solid sound points to brick or block, while a hollow one points to board on timber or metal. A wall that sounds hollow in patches and solid in others is usually plasterboard stuck to block with dabs of adhesive, known as dot-and-dab.

Irish homes add one trap. Dublin Assembly Pros notes that many Irish houses from the 1970s on were built in hollow block. It looks and sounds solid, but needs cavity fixings, not standard plugs. A stud detector helps find timber, and the drill tells you the rest within the first few millimetres.

Which fixings suit each wall type?

Short answer

Timber stud: screw into the studs, with cavity fixings between them. Metal stud: cavity fixings or a plywood pattress. Dot-and-dab: fix right through to the blockwork. Hollow block: cavity fixings. Solid block or brick: masonry plugs. Concrete: heavy-duty masonry fixings and bits.

TV fixings by wall type
Wall typeHow it sounds and drillsFixing that works
Plasterboard on timber studsHollow, timber every few hundred mmScrews into studs, cavity fixings between
Plasterboard on metal studsHollow, metal behindCavity fixings or a plywood pattress
Dot-and-dab on blockHollow and solid in patchesFix through to the blockwork
Hollow blockSolid knock, drill breaks throughCavity fixings, not standard plugs
Solid block, brick or concreteSolid, dusty drillingMasonry plugs or heavy-duty anchors

For a heavy TV on a timber stud wall, Smart Aerials, a UK installer, describes cutting a section of board and fitting plywood between the studs. That gives a solid panel to screw into, hidden behind the TV, which then gets patched.

How much weight can plasterboard fixings hold?

Short answer

More than most people expect when the load hangs straight down, and far less when it pulls outwards. GripIt’s datasheet gives 113 kg safe shear load for its 25 mm fixing and 93 kg for the 20 mm. Pulled straight out of the wall, every size is rated at only 20 kg.

GripIt safe static loads per fixing, 15 mm plasterboard
Load type20 mm (brown)25 mm (blue)
Shear: flat to the wall, e.g. a fixed TV bracket93 kg113 kg
Tension: pulled straight out20 kg20 kg
Cantilever: 50 mm from the wall36 kg40 kg
Cantilever: 75 mm from the wall29 kg31 kg
Cantilever: 150 mm from the wall24 kg25 kg

Source: GripIt GR0049 data sheet, independently tested on 15 mm plasterboard. GripIt says safe loads fall on thinner board, with 9.5 mm the minimum. It also says not to fix into damp, weak or damaged board, and to keep 25 mm fixings at least 100 mm apart.

Other brands publish their own figures. Use the loads printed for the exact fixing you buy, not a figure from a different product.

Not sure what your wall is?

Send a photo of the wall and the TV model, and we will tell you what we would use.

Does a full-motion bracket change things?

Short answer

Yes, a lot. An arm holds the TV away from the wall, which turns the load into a lever. The Assembly Crew says a full-motion arm puts more strain on the wall. GripIt’s own figures show why: at 150 mm out, the 25 mm fixing’s safe load falls from 113 kg to 25 kg.

GripIt also warns that repeated loading and unloading weakens plasterboard. A swinging arm does that every time it is pulled out and pushed back. On a hollow wall, a full-motion bracket should go into studs or a plywood pattress. Otherwise choose a fixed or tilting bracket that sits close to the wall.

Samsung says any VESA-compliant mount made for the screen size will fit its TVs, and gives 400 by 400 as the usual pattern from 46 to 75 inches. Check the bracket’s weight rating as well as its pattern.

How do you fix a TV to a dot-and-dab wall?

Short answer

Go through the board and fix into the masonry, with longer screws or coach bolts. Smart Aerials says standard cavity anchors will not fit in the narrow gap behind the board. It also warns against overtightening, which can crack the plasterboard as the bracket pulls it towards the block.

The gap behind dot-and-dab board varies. Where it is wide, a spacer or packing behind the bracket stops the board crushing. GripIt says its fixings work on dot-and-dab and insulated board with its undercutting tool, but that only spreads the load on the board itself. For a large TV, the block behind is the stronger fixing.

Can the cables go inside a plasterboard wall?

Short answer

Usually yes, because the wall is hollow. PROMOUNT, a Bray installer, lists hiding cables inside a hollow wall from €40, against from €20 for an external plastic conduit. Low-voltage leads such as HDMI can be fished down inside. A new power point is a job for a registered electrician.

On the HSA’s list, a new circuit counts as Restricted Works, so only a Registered Electrical Contractor may install it. Even a spur off an existing circuit must meet the wiring rules. We run TV leads inside the wall, but any socket work is for your electrician.

If the wall is above a fireplace, heat changes the answer. Our guide to a TV over a fireplace covers that. For prices by screen size, see our guide to TV wall mounting cost.

Need a price for tv wall mounting?

Send the plan or a photo and we will price it.

Frequently asked questions

Can a plasterboard wall hold a 65 inch TV?

Usually, if the bracket is fixed into studs or with cavity fixings rated well above the combined weight of the TV and bracket. Check the TV's weight in its manual. A fixed or tilting bracket is easier on the wall than a full-motion arm.

Are ordinary plastic wall plugs OK in plasterboard?

No, not for a TV. Plugs made for masonry have nothing to grip in a hollow wall. Use fixings made for plasterboard, or screw into the studs behind it.

How many fixings does a TV bracket need on plasterboard?

Use every fixing hole the bracket maker provides. GripIt's datasheet says to use the maximum recommended number of fixings and to keep its 25 mm fixings at least 100 mm apart.

Can I mount a TV on an insulated plasterboard wall?

Insulated board, often called warmboard, has a thick foam layer between the plasterboard and the block. Fixings need to reach the block behind. GripIt says its fixings work on insulated board with its undercutting tool, but check the length against the board thickness.

Will the TV pull the plasterboard off the wall over time?

It can if the fixings are overloaded or the board is damp or damaged. GripIt warns that repeated loading and unloading weakens plasterboard, which is what a full-motion arm does every time it is pulled out.

Do I need permission to mount a TV in a rented apartment?

Check your lease and ask your landlord first. A bracket leaves holes when it comes off, and some management companies have rules about fixing into party walls.

Next steps

How we checked these figures

Fixing loads come from the fixing maker's own datasheet (GripIt), loaded on 19 November 2026. We tried to load British Gypsum and Gyproc Ireland fixing guidance and Fischer's product pages, but they refused automated requests, so no figures from them are used. Descriptions of Irish wall types come from Irish installers' pages and are written as general guidance. One UK installer's how-to is used for the dot-and-dab method only. We used no forum posts. Always follow the loads and spacing in the instructions for the fixing and the bracket you are using.

Where the numbers come from

  1. Fixing heavy stuff to plasterboard (GR0049 UK data sheet), GripIt Fixings, checked 19 November 2026
  2. Things to consider before mounting your Samsung TV to a wall, Samsung (US support), checked 19 November 2026
  3. TV and wall mounting, The Assembly Crew, checked 19 November 2026
  4. TV mounting Tallaght (Irish wall types), Dublin Assembly Pros (furnitureassemblydublin.ie), checked 19 November 2026
  5. How to safely wall mount a TV to stud and drylined plasterboard walls, Smart Aerials (UK), checked 19 November 2026
  6. TV wall mounting Dublin and Wicklow, PROMOUNT, checked 19 November 2026
  7. Works needing certification, Health and Safety Authority, checked 19 November 2026
01 230 8966WhatsApp
Chat on WhatsApp